Milliput

Milliput 02 Terracotta Milliput

Terracotta Milliput - Image 1
Fabricante: Milliput
Código de producto: MPT02
Disponibilidad actual: 2-6 semanas
€5.60 o 3700 pts.

Incluido 21% de iva
al enviar al país: España
Para cambiar el país haga clic aquí

Información básica

FabricanteMilliput
Código de artículoMPT02
Peso0.12 kg
Ean:5035167000513
Capacidad113g
Añadido al catálogo:17.12.2015
TagsEpoxy-Putty

Terracotta Milliput

Milliput is a versatile manipulative two part epoxy putty which when mixed together sets rock hard. When first mixed, the putty is pliable and easily shaped. By wetting the Milliput with a finely woven moist cloth a very smooth finish can be easily obtained. Terracotta Milliput has been featured in the gardening sections of national newspapers and leading gardening magazines. Recommned products: Standard Milliput, Epoxy Putty Quick Dry and BROWN Stuff Kneadatite 15cm (6inches).

Typical applications:

  • Modelmaking
  • Sculpting
  • Picture frame restoration
  • Repair of Terracotta pots
  • Garden urns
  • Damaged brickwork
  • Quarry tiles internally and externally
  • Underwater applications

Using Milliput - A two part epoxy putty

Milliput is the trade name for our epoxy putty. We produce five grades: Standard (Yellow/Grey), Terracotta, Silver Grey, Black and Superfine White. Each grade is presented in similar packs containing 2 x 56,7gm. sticks and the general instructions for preparation and usage are the same.

Once equal quantities of each stick have been mixed the resultant putty is at first soft and highly adhesive and then gradually hardens. Speed of hardening is dependant on temperature and at normal temperatures (20-25 deg C) Milliput becomes rock hard in three to four hours. By the application of heat the setting time can be reduced.

After setting hard Milliput continues to cure and is fully cured after an elapse of time equal to the setting time at the same temperature. Once fully cured Milliput can be machined, drilled, tapped, turned, filed, sawn, sandpapered and painted.

Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive. Milliput will set under water and is heat resistant up to 130°C.

Mix together equal parts of each stick from the pack. Knead and roll in the hands for at least 5 minutes until the colours merge and become uniform and no streaks can be seen, and then mix for another minute. The surfaces to which the putty is applied should be free from grease and dirt. Smooth surfaces should be cleaned with a suitable solvent or with soap and warm water to remove dirt and grease. Abrading the surface will improve adhesion. the putty may now be applied and will set hard in three to four hours without shrinking.

At all stages from initial mixing to final setting Milliput responds to the use of water. To aid manipulation and avoid sticking, fingers and tools should be kept moistened with water. There are certain instances when work may be carried out in a gentle stream of water under a tap. To obtain a smooth finish, mould or apply Milliput and then immediately wipe and smooth gently with wet finger or with a fine textured moist cloth.

When tools have been used for applying or contouring Milliput they should be cleaned immediately after use. If the putty is allowed to harden on it will be almost impossible to remove.

In the putty state Milliput, like most chemicals in domestic use, may cause irritation to sensitive skins. When mixing the two components it is advisable to use rubber gloves or throw-away polythene gloves. When rubber gloves have been used wash them immediately after use, and whilst still on the hands, using running water. If the hands have been used for mixing or manipulating Milliput wash them immediately after use with toilet soap and warm water.

When casting or mouldmaking talc or a light oil can be used as a releasing agent.

Milliput products are resistant to frost, heat, solvents and most fuels.

Colouring Milliput

There are a number of ways of colouring Milliput.

Different colours can be obtain by cross-mixing or blending from the range of colours that Milliput is available in.

Powder pigment can be mixed in, in small quantities, so that the mixture does not become too dry and crumbly. Strong powder pigment rather than powder paint is better as smaller amounts can be used.

Liquid colourings, like enamel paints, oil paints, spirit based-dyes or pigments can also be used to colour Milliput, but liquids or pastes may be difficult to introduce into the putty, again small quantities should be used, to avoid creating a very wet mix that may be difficult to mix.

In all cases the Milliput should be thoroughly mixed by rolling & folding about 30-35 times. This will ensure that all the hardener has come in good contact with the resin and the Milliput will then set correctly.

¿Hay un error en la descripción? Avisar de un problema
Opiniones de nuestros clientes
Añade tu opinión sobre: Terracotta Milliput
...
Añadido al catálogo: 17.12.2015
Disponibilidad actual: 2-6 semanas
  • artículo disponible
  • artículo no disponible
  • artículo disponible a pedido
  • entrega de mercancía
  • no hay
  • 1 unidad
  • 2 unidades
  • 3-5 unidades
  • 6-10 unidades
  • más de 10 unidades
¿Podemos traer un artículo que no está en la página o no está disponible?
Artículos similares

Fabricante: Milliput
Código de producto: MPT05
Disponibilidad: ¡disponible!

€11.65 o 7700 pts.

Fabricante: Milliput
Código de producto: MPT01
Disponibilidad: ¡disponible!

€6.87 o 4500 pts.

Fabricante: Milliput
Código de producto: MPT06
Disponibilidad: ¡disponible!

€12.21 o 8000 pts.

Fabricante: Milliput
Código de producto: MPT04
Disponibilidad: ¡disponible!

€9.95 o 6600 pts.

Fabricante: Milliput
Código de producto: MPT03
Disponibilidad: ¡disponible!

€9.34 o 6200 pts.

Fabricante: Green Stuff World
Código de producto: GSW9003
Disponibilidad: ¡disponible!

€8.49 o 5600 pts.

Fabricante: Green Stuff World
Código de producto: GSW9004
Disponibilidad: ¡disponible!

€6.08 o 4000 pts.

Fabricante: Green Stuff World
Código de producto: GSW9002
Disponibilidad: ¡disponible!

€11.55 o 7600 pts.

Fabricante: Tamiya
Código de producto: tam87145
Disponibilidad: ¡disponible!

€22.08 o 13900 pts.

Fabricante: Tamiya
Código de producto: tam87143
Disponibilidad: ¡disponible!

€21.66 o 13600 pts.

Fabricante: Tamiya
Código de producto: tam87052
Disponibilidad: ¡disponible!

€6.55 o 4100 pts.

Fabricante: Tamiya
Código de producto: tam87051
Disponibilidad: ¡disponible!

€6.63 o 4200 pts.